Preliminary Datasheet P9415 (IDT) - 3
| Fabricante | IDT |
| Descripción | Medium Power Wireless Transmitter/Receiver (TRx) |
| Páginas / Página | 26 / 3 — Table 1. Pin Descriptions. Type. Description |
| Revisión | 20190829 |
| Formato / tamaño de archivo | PDF / 1.3 Mb |
| Idioma del documento | Inglés |
Table 1. Pin Descriptions. Type. Description
Línea de modelo para esta hoja de datos
Versión de texto del documento
P9415 Preliminary Datasheet
Table 1. Pin Descriptions
Number Name
Type Description
A1 COM1 O High-voltage open-drain modulation FET. Connect a capacitor from AC1 to COM1. A2 GP1 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. A3 OD0 I/O Clock for I2C Serial Interface with AP (SCL). Connect a pull-up resistor to the system I/O supply. A4 OD3 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. A5 GP4 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. A6 COM2 O High-voltage open-drain modulation FET. Connect a capacitor from AC2 to COM2. B1 CMA O High-voltage open-drain modulation FET. Connect a capacitor from AC1 to CMA. B2 GP0 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. B3 OD1 I/O Data for I2C Serial Interface with AP (SDA). Connect a pull-up resistor to the system I/O supply. B4 OD4 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. B6 CMB O High-voltage open-drain modulation FET. Connect a capacitor from AC2 to CMB. C3 OD2 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. ECLAMP_D Push-Pull output driver for External Power Clamp FET gate control (Connect a resistor from Vrect to the C4 RV O external FET to GND). May be floating if not used. C5 GP2 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D1 LDO5P0 O Internal 5V LDO for chip power only (always On when Vrect is powered). Connect a capacitor to ground. D2 GP5 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D3 PCLAMP I High voltage open drain input for linear clamping during OVP events. Connect a resistor from this pin to VRECT for >5W operation. Short directly to VRECT for 5W or lower power applications. D4 GP3 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D5 GP6 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. © 2019 IDT A Renesas Company. 3 Revision 0.8 August 29, 2019
Table 1. Pin Descriptions
Number Name
Type Description
A1 COM1 O High-voltage open-drain modulation FET. Connect a capacitor from AC1 to COM1. A2 GP1 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. A3 OD0 I/O Clock for I2C Serial Interface with AP (SCL). Connect a pull-up resistor to the system I/O supply. A4 OD3 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. A5 GP4 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. A6 COM2 O High-voltage open-drain modulation FET. Connect a capacitor from AC2 to COM2. B1 CMA O High-voltage open-drain modulation FET. Connect a capacitor from AC1 to CMA. B2 GP0 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. B3 OD1 I/O Data for I2C Serial Interface with AP (SDA). Connect a pull-up resistor to the system I/O supply. B4 OD4 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. B6 CMB O High-voltage open-drain modulation FET. Connect a capacitor from AC2 to CMB. C3 OD2 I/O General Purpose Open Drain I/O, referenced to LDO1P8. May be floating if not used. ECLAMP_D Push-Pull output driver for External Power Clamp FET gate control (Connect a resistor from Vrect to the C4 RV O external FET to GND). May be floating if not used. C5 GP2 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D1 LDO5P0 O Internal 5V LDO for chip power only (always On when Vrect is powered). Connect a capacitor to ground. D2 GP5 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D3 PCLAMP I High voltage open drain input for linear clamping during OVP events. Connect a resistor from this pin to VRECT for >5W operation. Short directly to VRECT for 5W or lower power applications. D4 GP3 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. D5 GP6 I/O General Purpose Push-Pull I/O, referenced to LDO1P8. May be floating if not used. © 2019 IDT A Renesas Company. 3 Revision 0.8 August 29, 2019