Datasheet AD8132 (Analog Devices) - 7
Fabricante | Analog Devices |
Descripción | Low Cost, High Speed Differential Amplifier |
Páginas / Página | 33 / 7 — AD8132. ±DIN TO ±OUT SPECIFICATIONS. Table 3. Parameter Conditions. Min. … |
Revisión | I |
Formato / tamaño de archivo | PDF / 518 Kb |
Idioma del documento | Inglés |
AD8132. ±DIN TO ±OUT SPECIFICATIONS. Table 3. Parameter Conditions. Min. Typ. Max. Unit
Línea de modelo para esta hoja de datos
Versión de texto del documento
link to page 21 link to page 21
AD8132 ±DIN TO ±OUT SPECIFICATIONS
At TA = 25°C, VS = 5 V, VOCM = 2.5 V, G = +1, RL, dm = 499 Ω, RF = RG = 348 Ω, unless otherwise noted. For G = +2, RL, dm = 200 Ω, RF = 1000 Ω, RG = 499 Ω. Refer to Figure 56 and Figure 57 for test setup and label descriptions. All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 3. Parameter Conditions Min Typ Max Unit
DYNAMIC PERFORMANCE −3 dB Large Signal Bandwidth VOUT = 2 V p-p 250 300 MHz AD8132W only, TMIN to TMAX 240 MHz VOUT = 2 V p-p, G = +2 180 MHz −3 dB Small Signal Bandwidth VOUT = 0.2 V p-p 360 MHz VOUT = 0.2 V p-p, G = +2 155 MHz Bandwidth for 0.1 dB Flatness VOUT = 0.2 V p-p 65 MHz VOUT = 0.2 V p-p, G = +2 50 MHz Slew Rate VOUT = 2 V p-p 800 1000 V/μs AD8132W only, TMIN to TMAX 750 V/μs Settling Time 0.1%, VOUT = 2 V p-p 20 ns Overdrive Recovery Time VIN = 2.5 V to 0 V step, G = +2 5 ns NOISE/HARMONIC PERFORMANCE Second Harmonic VOUT = 2 V p-p, 1 MHz, RL, dm = 800 Ω −97 dBc VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω −100 dBc VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω −74 dBc Third Harmonic VOUT = 2 V p-p, 1 MHz, RL, dm = 800 Ω −100 dBc VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω −99 dBc VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω −67 dBc IMD 20 MHz, RL, dm = 800 Ω −76 dBc IP3 20 MHz, RL, dm = 800 Ω 40 dBm Input Voltage Noise (RTI) f = 0.1 MHz to 100 MHz 8 nV/√Hz Input Current Noise f = 0.1 MHz to 100 MHz 1.8 pA/√Hz Differential Gain Error NTSC, G = +2, RL, dm = 150 Ω 0.025 % Differential Phase Error NTSC, G = +2, RL, dm = 150 Ω 0.15 Degrees INPUT CHARACTERISTICS Offset Voltage (RTI) VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = VOCM = 2.5 V ±1.0 ±3.5 mV AD8132W only, TMIN to TMAX ±6 mV TMIN to TMAX variation 6 μV/°C Input Bias Current TA = 25°C 3 7 μA 8 μA Input Resistance Differential AD8132W only, TMIN to TMAX 10 MΩ Common-mode 3 MΩ Input Capacitance 1 pF Input Common-Mode Voltage 0.3 to 3.0 V CMRR ΔVOUT, dm/ΔVIN, cm; ΔVIN, cm = ±1 V; resistors matched to 0.01% −70 −60 dB AD8132W only, TMIN to TMAX −60 dB OUTPUT CHARACTERISTICS AD8132W only, TMIN to TMAX Output Voltage Swing Maximum ΔVOUT; single-ended output 1.0 to 4.0 V Output Current 50 mA Output Balance Error ΔVOUT, cm/ΔVOUT, dm; ΔVOUT, dm = 1 V −68 dB Rev. I | Page 6 of 32 Document Outline FEATURES APPLICATIONS GENERAL DESCRIPTION CONNECTION DIAGRAM TABLE OF CONTENTS REVISION HISTORY SPECIFICATIONS ±DIN TO ±OUT SPECIFICATIONS VOCM TO ±OUT SPECIFICATIONS ±DIN TO ±OUT SPECIFICATIONS VOCM TO ±OUT SPECIFICATIONS ±DIN TO ±OUT SPECIFICATIONS VOCM TO ±OUT SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE MAXIMUM POWER DISSIPATION ESD CAUTION PIN CONFIGURATION AND FUNCTION DESCRIPTIONS TYPICAL PERFORMANCE CHARACTERISTICS TEST CIRCUITS OPERATIONAL DESCRIPTION DEFINITION OF TERMS Differential Voltage Common-Mode Voltage BASIC CIRCUIT OPERATION THEORY OF OPERATION GENERAL USAGE OF THE AD8132 DIFFERENTIAL AMPLIFIER WITHOUT RESISTORS (HIGH INPUT IMPEDANCE INVERTING AMPLIFIER) OTHER β2 = 1 CIRCUITS VARYING β2 β1 = 0 ESTIMATING THE OUTPUT NOISE VOLTAGE CALCULATING INPUT IMPEDANCE OF THE APPLICATION CIRCUIT INPUT COMMON-MODE VOLTAGE RANGE IN SINGLE-SUPPLY APPLICATIONS SETTING THE OUTPUT COMMON-MODE VOLTAGE DRIVING A CAPACITIVE LOAD OPEN-LOOP GAIN AND PHASE LAYOUT, GROUNDING, AND BYPASSING CIRCUITS APPLICATIONS INFORMATION ANALOG-TO-DIGITAL DRIVER BALANCED CABLE DRIVER TRANSMIT EQUALIZER LOW-PASS DIFFERENTIAL FILTER HIGH COMMON-MODE OUTPUT IMPEDANCE AMPLIFIER FULL-WAVE RECTIFIER AUTOMOTIVE PRODUCTS OUTLINE DIMENSIONS ORDERING GUIDE