Datasheet SiC951 (Vishay) - 9

FabricanteVishay
Descripción4.5 V to 20 V Input, 25 A MicroBRICK DC/DC Regulator Module With PMBus Interface
Páginas / Página28 / 9 — SiC951. PMBus COMMAND COMM. PMBus. COMM. # DATA. DEFAULT. EXP. VALID. …
Formato / tamaño de archivoPDF / 3.1 Mb
Idioma del documentoInglés

SiC951. PMBus COMMAND COMM. PMBus. COMM. # DATA. DEFAULT. EXP. VALID. DESCRIPTION. CODES. COMMANDS. STRUCT. BYTES. VALUE. (FIXED). VALUES

SiC951 PMBus COMMAND COMM PMBus COMM # DATA DEFAULT EXP VALID DESCRIPTION CODES COMMANDS STRUCT BYTES VALUE (FIXED) VALUES

Línea de modelo para esta hoja de datos

Versión de texto del documento

SiC951
www.vishay.com Vishay Siliconix
PMBus COMMAND COMM. PMBus COMM. # DATA DEFAULT EXP. VALID DESCRIPTION DEFAULT CODES COMMANDS STRUCT. BYTES VALUE (FIXED) VALUES
Sets VOUT format bit 7 0: absolute 1: relative bit 6 and 5 00: ULINEAR16 / SLINEAR16 01: VID 10: direct 0x20 VOUT_MODE Byte 1 0x17 -9 11: IEEE half precision FP bit 4, 3, and 2 ULINEAR16 : N (X = VOUT_COMMANDx2^N) = -9 (10111) VID: VID code type Direct: 00000 IEEE: 00000 Sets V 0x21 VOUT_COMMAND Word OUT (V) 2 0x0133 0.6 -9 0.3-14 2 bytes SLINEAR16 User trimming offset to be added in SLINEAR16 format 0x22 VOUT_TRIM Word 2 0x0000 0 -9 (-2)-2 (2's complement) (V) 2 bytes SLINEAR16 Sets maximum VOUT for alert and 0x24 VOUT_MAX limiting VOUT (V) 2 0x1C00 14 -9 0.3-14 2 bytes SLINEAR16 5 % 0x25 VOUT_MARGIN_HIGH Word Set the MARGIN HIGH voltage 2 0x0142 0.63 -9 0.3-14 2 bytes SLINEAR16 -5 % 0x26 VOUT_MARGIN_LOW Word Set the MARGIN LOW voltage 2 0x0123 0.57 -9 0.3-14 2 bytes SLINEAR16 11 Sets the slew rate in mV/μs 0x27 VOUT_TRANSITION_RATE Word 2 0xE002 0.125 -4 0.0625-2 2 bytes ULINEAR11 Sets the VOUT/FB ratio 0.125, 0.25, 0x29 VOUT_SCALE_LOOP Word 2 bytes SLINEAR11, 0.125,0.25, 0.5, 1 2 0xE808 1 -3 0.5, 1 allowed Switching frequency: (kHz) 300K to 0x33 FREQUENCY_SWITCH Word 2 bytes LINEAR11, 2 0x0258 600 0 1500K, (200K to 1500K, 50K steps) 50K steps V 0x35 VIN_ON Word IN in which the device starts 2 0xF814 10 -1 1-80 2 bytes SLINEAR11 V 0x36 VIN_OFF Word IN in which the device stops 2 0xF812 9 -1 1-80 2 bytes SLINEAR11 Set master / slave clock 0° or 180° See 0x37 Interleave Word out of phase. See INTERLEAVE 2 0x0000 0 INTERLEAVE description for detail description Sets the OVP DAC level above VOUT in digital mode 0x40 VOUT_OV_FAULT_LIMIT Word 2 0x0161 0.69 -9 0.3-14 Default analog = 115 % VOUT 2 bytes SLINEAR16 Bit 7, 6 to 11: shut down until fault is disabled bit 3, 4, and 5 - 111: According 0x41 VOUT_OV_FAULT_RESPONSE Word 1 0xF8 All restart continuously to settings bit 0, 1, and 2 - 000: no delay Telemetry warn limit (V) 0x42 VOUT_OV_WARN_LIMIT Word 2 0x0151 0.66 -9 0.3-14 2 bytes SLINEAR16 Telemetry warn limit (V) 0x43 VOUT_UV_WARN_LIMIT Word 2 0x0114 0.54 -9 0-14 2 bytes SLINEAR16 S23-0736-Rev. C, 12-Sep-2023
9
Document Number: 71554 For technical questions, contact: powerictechsupport@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000