Datasheet HMC920LP5E (Analog Devices) - 7
| Fabricante | Analog Devices |
| Descripción | ACTIVE BIAS CONTROLLER |
| Páginas / Página | 26 / 7 — HMC920LP5E. ACTIVE BIAS CONTROLLER. Pin Descriptions. 13 - 7 |
| Formato / tamaño de archivo | PDF / 1.6 Mb |
| Idioma del documento | Inglés |
HMC920LP5E. ACTIVE BIAS CONTROLLER. Pin Descriptions. 13 - 7
Línea de modelo para esta hoja de datos
Versión de texto del documento
HMC920LP5E
v07.1013
ACTIVE BIAS CONTROLLER Pin Descriptions
Pin Number Function Description Interface Schematic Bias supply Pins. Connect supply voltage 1, 2 Vdd1 to all these pins with appropriate filtering. Vdd1 supply voltage should be same as Vdd2. 3.5V LDO output for internal use. Output capability <30mA. 3 VDIG Is not recommended for external use. Feedback node for VDIG LDO. Should be left floating for 4 VDIGFB regular operation. 13 External capacitor for power-on-reset signal. 47pF to 5 PORCAP GND is needed. If longer POR duration is needed, can be increased. T A resistor to ground is needed. The value of the resistor 10 ALMSET determines the alarm delay duration. The value of the M resistor can be chosen between 10K and 10M. A high precision (e.g. 0.5%, ±25 ppm TCR) 10K resistor 12 FIXBIAS to ground is needed. Variance in the resistance will cause deviation in the bias current. T - S N E M External capacitor of bandgap output. Connect a 6 BGCAP E 0.1uF or greater low ESR ceramic capacitor to GND. G A N A Enable pin. System is enabled when Ven is HIGH (3.5V). IF 7 EN left floating, Ven defaults to HIGH (enabled). R M E W Dummy alarm trigger signal to create test alarm when O 9 ALMTRG taken HIGH (3.5V). Defaults to LOW (GND) when left floating. C P D Over/under current alarm 8 CURALM (Generates an active HIGH signal). Trigger out signal. Generates a HIGH (3.5V) signal when the active bias system stabilizes. This signal can be 24 TRGOUT used to trigger next device (ENABLE) if more than one HMC920LP5E is used in a daisy chain. 31 VddALM Generates an active LOW signal if Vdd1 drops below 3.5V. Information furnish F e o d r p by A rnic alo e g , d Devi ecleis vie s rby eli, a eve nd t d to b o p e a l cc a ur c at e o e an r d d releiars ble , p . Ho le we a ve sr, e c no For price, delivery, and to place orders: Analog Devices, Inc., responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other ontact Hittite Microwave Corporation: One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone rights of third parties that may result from its use. Specifications subject to change without notice. No : 9P7 h 8 o - n 2 e 5 : 7 0- 81- 3 3 3 2 4 9- 3 F 470 ax: 9 0 • Ord 7 e 8 r o - n 2 li 5 n 0 e a-t 337 ww 3
13 - 7
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. w.analog.com Order On- Trademarks and registered trademarks are the property of their respective owners. line at www.hi A tptiptliec.actio o m n Support: Phone: 1-800-ANALOG-D
v07.1013
ACTIVE BIAS CONTROLLER Pin Descriptions
Pin Number Function Description Interface Schematic Bias supply Pins. Connect supply voltage 1, 2 Vdd1 to all these pins with appropriate filtering. Vdd1 supply voltage should be same as Vdd2. 3.5V LDO output for internal use. Output capability <30mA. 3 VDIG Is not recommended for external use. Feedback node for VDIG LDO. Should be left floating for 4 VDIGFB regular operation. 13 External capacitor for power-on-reset signal. 47pF to 5 PORCAP GND is needed. If longer POR duration is needed, can be increased. T A resistor to ground is needed. The value of the resistor 10 ALMSET determines the alarm delay duration. The value of the M resistor can be chosen between 10K and 10M. A high precision (e.g. 0.5%, ±25 ppm TCR) 10K resistor 12 FIXBIAS to ground is needed. Variance in the resistance will cause deviation in the bias current. T - S N E M External capacitor of bandgap output. Connect a 6 BGCAP E 0.1uF or greater low ESR ceramic capacitor to GND. G A N A Enable pin. System is enabled when Ven is HIGH (3.5V). IF 7 EN left floating, Ven defaults to HIGH (enabled). R M E W Dummy alarm trigger signal to create test alarm when O 9 ALMTRG taken HIGH (3.5V). Defaults to LOW (GND) when left floating. C P D Over/under current alarm 8 CURALM (Generates an active HIGH signal). Trigger out signal. Generates a HIGH (3.5V) signal when the active bias system stabilizes. This signal can be 24 TRGOUT used to trigger next device (ENABLE) if more than one HMC920LP5E is used in a daisy chain. 31 VddALM Generates an active LOW signal if Vdd1 drops below 3.5V. Information furnish F e o d r p by A rnic alo e g , d Devi ecleis vie s rby eli, a eve nd t d to b o p e a l cc a ur c at e o e an r d d releiars ble , p . Ho le we a ve sr, e c no For price, delivery, and to place orders: Analog Devices, Inc., responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other ontact Hittite Microwave Corporation: One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone rights of third parties that may result from its use. Specifications subject to change without notice. No : 9P7 h 8 o - n 2 e 5 : 7 0- 81- 3 3 3 2 4 9- 3 F 470 ax: 9 0 • Ord 7 e 8 r o - n 2 li 5 n 0 e a-t 337 ww 3
13 - 7
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. w.analog.com Order On- Trademarks and registered trademarks are the property of their respective owners. line at www.hi A tptiptliec.actio o m n Support: Phone: 1-800-ANALOG-D