Datasheet TDA8566 (NXP) - 9
| Fabricante | NXP |
| Descripción | 2 x 40 W/2 ohm stereo BTL car radio power amplifier with differential inputs and diagnostic outputs |
| Páginas / Página | 21 / 9 — NXP Semiconductors. TDA8566. 40 W/2. stereo BTL car radio power … |
| Formato / tamaño de archivo | PDF / 132 Kb |
| Idioma del documento | Inglés |
NXP Semiconductors. TDA8566. 40 W/2. stereo BTL car radio power amplifier. 10. Static characteristics. Table 7
Línea de modelo para esta hoja de datos
TDA8566Q
- TDA8566Q/N1,112 TDA8566Q/N1/S420,1 TDA8566Q/N2,112 TDA8566Q/N2/S438,1 TDA8566Q/N2C,112 TDA8566Q/N2S,112
- TDA8566TH/N2,112 TDA8566TH/N2,118 TDA8566TH/N2,512 TDA8566TH/N2,518 TDA8566TH/N2C,112 TDA8566TH/N2C,118 TDA8566TH/N2S,112 TDA8566TH/N2S,118
TDA8566TH1
Versión de texto del documento
link to page 12 link to page 9 link to page 9 link to page 9
NXP Semiconductors TDA8566 2
×
40 W/2
Ω
stereo BTL car radio power amplifier 10. Static characteristics Table 7. Static characteristics
VP = 14.4 V; Tamb = 25 °C; measured in test circuit of Figure 9; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit Supply
VP supply voltage [1] 6 14.4 18 V Iq quiescent current RL = ∞ Ω - 115 180 mA
Operating condition
VMODE mode select switch 8.5 - VP V level IMODE mode select switch VMODE = 14.4 V - 15 40 µA current VO output voltage [2] - 7.0 - V VOO output offset voltage - - 100 mV
Mute condition
VMODE mode select switch 3.3 - 6.4 V level VO output voltage [2] - 7.0 - V VOO output offset voltage - - 60 mV ∆VOO output offset voltage with respect to - - 60 mV difference operating condition
Standby condition
VMODE mode select switch 0 - 2 V level Istb standby current - 0.1 10 µA
Diagnostic
VDIAG diagnostic output during any fault - - 0.6 V voltage condition [1] The circuit is DC adjusted at VP = 6 V to 18 V and AC operating at VP = 8.5 V to 18 V. [2] At VP = 18 V to 30 V the DC output voltage is ≤ 0.5VP. TDA8566_6 © NXP B.V. 2007. All rights reserved.
Product data sheet Rev. 06 — 15 October 2007 9 of 21
Document Outline 1. General description 2. Features 3. Quick reference data 4. Ordering information 5. Block diagram 6. Pinning information 6.1 Pinning 6.2 Pin description 7. Functional description 7.1 Mode select switch (pinMODE) 7.2 Clip detection (pinCLIP) 7.3 Short-circuit diagnostic (pinDIAG) 7.4 Temperature pre-warning (pinDIAG) 7.5 Open-collector diagnostic outputs 7.6 Differential inputs 8. Limiting values 9. Thermal characteristics 10. Static characteristics 11. Dynamic characteristics 12. Application information 12.1 Diagnostic output 12.2 Mode select switch 13. Test information 14. Package outline 15. Soldering 15.1 Introduction to soldering 15.2 Wave and reflow soldering 15.3 Wave soldering 15.4 Reflow soldering 16. Revision history 17. Legal information 17.1 Data sheet status 17.2 Definitions 17.3 Disclaimers 17.4 Trademarks 18. Contact information 19. Contents
NXP Semiconductors TDA8566 2
×
40 W/2
Ω
stereo BTL car radio power amplifier 10. Static characteristics Table 7. Static characteristics
VP = 14.4 V; Tamb = 25 °C; measured in test circuit of Figure 9; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit Supply
VP supply voltage [1] 6 14.4 18 V Iq quiescent current RL = ∞ Ω - 115 180 mA
Operating condition
VMODE mode select switch 8.5 - VP V level IMODE mode select switch VMODE = 14.4 V - 15 40 µA current VO output voltage [2] - 7.0 - V VOO output offset voltage - - 100 mV
Mute condition
VMODE mode select switch 3.3 - 6.4 V level VO output voltage [2] - 7.0 - V VOO output offset voltage - - 60 mV ∆VOO output offset voltage with respect to - - 60 mV difference operating condition
Standby condition
VMODE mode select switch 0 - 2 V level Istb standby current - 0.1 10 µA
Diagnostic
VDIAG diagnostic output during any fault - - 0.6 V voltage condition [1] The circuit is DC adjusted at VP = 6 V to 18 V and AC operating at VP = 8.5 V to 18 V. [2] At VP = 18 V to 30 V the DC output voltage is ≤ 0.5VP. TDA8566_6 © NXP B.V. 2007. All rights reserved.
Product data sheet Rev. 06 — 15 October 2007 9 of 21
Document Outline 1. General description 2. Features 3. Quick reference data 4. Ordering information 5. Block diagram 6. Pinning information 6.1 Pinning 6.2 Pin description 7. Functional description 7.1 Mode select switch (pinMODE) 7.2 Clip detection (pinCLIP) 7.3 Short-circuit diagnostic (pinDIAG) 7.4 Temperature pre-warning (pinDIAG) 7.5 Open-collector diagnostic outputs 7.6 Differential inputs 8. Limiting values 9. Thermal characteristics 10. Static characteristics 11. Dynamic characteristics 12. Application information 12.1 Diagnostic output 12.2 Mode select switch 13. Test information 14. Package outline 15. Soldering 15.1 Introduction to soldering 15.2 Wave and reflow soldering 15.3 Wave soldering 15.4 Reflow soldering 16. Revision history 17. Legal information 17.1 Data sheet status 17.2 Definitions 17.3 Disclaimers 17.4 Trademarks 18. Contact information 19. Contents