Datasheet AL8861Q (Diodes) - 2
| Fabricante | Diodes |
| Descripción | High Efficiency 40V 1.5A Automotive Grade Buck LED Driver |
| Páginas / Página | 15 / 2 — AL8861Q. Typical Applications Circuit. T C U D O R P. W E. Pin … |
| Formato / tamaño de archivo | PDF / 666 Kb |
| Idioma del documento | Inglés |
AL8861Q. Typical Applications Circuit. T C U D O R P. W E. Pin Descriptions. Pin Number. Pin Name. Function. Functional Block Diagram
Línea de modelo para esta hoja de datos
Versión de texto del documento
AL8861Q Typical Applications Circuit
VIN (4.5V to 40V)
T C U D O R P W E Pin Descriptions N Pin Number Pin Name Function
Connect resistor RS from this pin to VIN to define nominal average output current. 1 ISENSE IOUTNOM = 0.1/RS 2,3 GND Ground (0V) Multi-function On/Off and Brightness Control Pin: Leave floating for normal operation Drive voltage below 0.2V to turn off output current Drive with DC voltage (0.3V < VSET < 2.5V) to adjust output current from 0 to 100% of IOUTNOM. 4 VSET Linear adjustment range from 5% to 100% of IOUTNOM Drive with PWM signal from open-collector or open-drain transistor to adjust output current. Linear adjustment range from 1% to 100% of IOUTNOM for f < 500Hz Connect a capacitor from this pin to Ground to increase soft-start time. (Default soft-start time = 0.1ms. Additional soft-start time is approximately 1.5ms/1nF) 5, 6 LX Drain of NDMOS switch. 7 N/C No Connection Input voltage (4.5V to 40V). Decouple to Ground with 10μF or higher X7R ceramic capacitor close to 8 VIN device. Exposed Pad. Connect to GND and thermal mass for enhanced thermal impedance. Should not be used EP EP as electrical ground conduction path.
Functional Block Diagram
ISENSE LX 1 5, 6 8 VIN 4.5V VDD Current Current 4.5V Drv Generator Monitor Limiter Comp BG & Ref Hysteresis Logic & Reference Control PWM Driver PWM/DC PWM OTP VSET OTP 4 Dimming 2, 3 GND AL8861Q 2 of 15 May 2019 Document number: DS41798 Rev. 2 - 2
www.diodes.com
© Diodes Incorporated
VIN (4.5V to 40V)
T C U D O R P W E Pin Descriptions N Pin Number Pin Name Function
Connect resistor RS from this pin to VIN to define nominal average output current. 1 ISENSE IOUTNOM = 0.1/RS 2,3 GND Ground (0V) Multi-function On/Off and Brightness Control Pin: Leave floating for normal operation Drive voltage below 0.2V to turn off output current Drive with DC voltage (0.3V < VSET < 2.5V) to adjust output current from 0 to 100% of IOUTNOM. 4 VSET Linear adjustment range from 5% to 100% of IOUTNOM Drive with PWM signal from open-collector or open-drain transistor to adjust output current. Linear adjustment range from 1% to 100% of IOUTNOM for f < 500Hz Connect a capacitor from this pin to Ground to increase soft-start time. (Default soft-start time = 0.1ms. Additional soft-start time is approximately 1.5ms/1nF) 5, 6 LX Drain of NDMOS switch. 7 N/C No Connection Input voltage (4.5V to 40V). Decouple to Ground with 10μF or higher X7R ceramic capacitor close to 8 VIN device. Exposed Pad. Connect to GND and thermal mass for enhanced thermal impedance. Should not be used EP EP as electrical ground conduction path.
Functional Block Diagram
ISENSE LX 1 5, 6 8 VIN 4.5V VDD Current Current 4.5V Drv Generator Monitor Limiter Comp BG & Ref Hysteresis Logic & Reference Control PWM Driver PWM/DC PWM OTP VSET OTP 4 Dimming 2, 3 GND AL8861Q 2 of 15 May 2019 Document number: DS41798 Rev. 2 - 2
www.diodes.com
© Diodes Incorporated