Datasheet LT1070, LT1071 (Linear Technology) - 3

FabricanteLinear Technology
Descripción5A and 2.5A High Efficiency Switching Regulators
Páginas / Página12 / 3 — ELECTRICAL CHARACTERISTICS The. denotes the specifications which apply …
RevisiónE
Formato / tamaño de archivoPDF / 218 Kb
Idioma del documentoInglés

ELECTRICAL CHARACTERISTICS The. denotes the specifications which apply over the full operating temperature

ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature

Línea de modelo para esta hoja de datos

Versión de texto del documento

LT1070/LT1071
ELECTRICAL CHARACTERISTICS The

denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25
°
C. VIN = 15V, VC = 0.5V, VFB = VREF, output pin open unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VFB Flyback Reference Voltage IFB = 50µA 15 16.3 17.6 V ● 14 18.0 V Change in Flyback Reference Voltage 0.05 ≤ IFB ≤ 1mA 4.5 6.8 8.5 V Flyback Reference Voltage Line Regulation IFB = 50µA, 3V ≤ VIN ≤ VMAX (Note 3) 0.01 0.03 %/V Flyback Amplifier Transconductance (gm) ∆IC = ±10µA 150 300 650 µmho Flyback Amplifier Source and Sink Current VC = 0.6V, IFB = 50µA (Source) ● 15 32 70 µA VC = 0.6V, IFB = 50µA (Sink) ● 25 40 70 µA BV Output Switch Breakdown Voltage 3V ≤ VIN ≤ VMAX, ISW = 1.5mA (LT1070/LT1071) ● 65 90 V (LT1070HV/LT1071HV) ● 75 90 V VSAT Output Switch “On” Resistance (Note 4) LT1070 ● 0.15 0.24 Ω LT1071 ● 0.30 0.50 Ω Control Voltage to Switch Current LT1070 8 A/V Transconductance LT1071 4 A/V ILIM Switch Current Limit (LT1070) Duty Cycle ≤ 50%, TJ ≥ 25°C ● 5 10 A Duty Cycle ≤ 50%, TJ < 25°C ● 5 11 A Duty Cycle = 80% (Note 5) ● 4 10 A Switch Current Limit (LT1071) Duty Cycle ≤ 50%, TJ ≥ 25°C ● 2.5 5.0 A Duty Cycle ≤ 50%, TJ < 25°C ● 2.5 5.5 A Duty Cycle = 80% (Note 5) ● 2.0 5.0 A ∆IIN Supply Current Increase During 25 35 mA/A ∆ISW Switch “On” Time f Switching Frequency 35 40 45 kHz ● 33 47 kHz DC (Max) Maximum Switch Duty Cycle 90 92 97 % Flyback Sense Delay Time 1.5 µs Shutdown Mode Supply Current 3V ≤ VIN ≤ VMAX, VC = 0.05V 100 250 µA Shutdown Mode Threshold Voltage 3V ≤ VIN ≤ VMAX 100 150 250 mV ● 50 300 mV
Note 1:
Absolute Maximum Ratings are those values beyond which the life of t = Minimum “on” time of LT1070/LT1071 in current limit, ≈1µs a device may be impaired. f = Operating frequency (40kHz)
Note 2:
Minimum switch “on” time for the LT1070/LT1071 in current limit is VF = Forward voltage of external catch diode at ILIMIT ≈1µs. This limits the maximum input voltage during short-circuit conditions, ILIMIT = Current limit of LT1070 (≈8A), LT1071 (≈ 4A) in the buck and inverting modes only, to ≈ 35V. Normal (unshorted) conditions RL = Internal series resistance of inductor are not affected. Mask changes are being implemented which will reduce
Note 3:
VMAX = 55V for LT1070HV and LT1071HV to avoid switch minimum “on” time to ≤ 1µs, increasing maximum short-circuit input voltage breakdown. above 40V. If the present LT1070/LT1071 (contact factory for package date
Note 4:
Measured with VC in hi clamp, VFB = 0.8V. ISW = 4A for LT1070 code) is being operated in the buck or inverting mode at high input voltages and 2A for LT1071. and short-circuit conditions are expected, a resistor must be placed in series
Note 5:
For duty cycles (DC) between 50% and 80%, minimum with the inductor, as follows: guaranteed switch current is given by ILIM = 3.33 (2 – DC) for the The value of the resistor is given by: LT1070 and ILIM = 1.67 (2 – DC) for the LT1071. t • f • V R = IN – VF – RL ILIMIT 10701fe 3