Datasheet ATtiny4, ATtiny5, ATtiny9, ATtiny10. Appendix A. Specification at 125C (Microchip) - 2
| Fabricante | Microchip |
| Descripción | 8-bit AVR Microcontroller with 512/1024 Bytes In-System Programmable Flash |
| Páginas / Página | 34 / 2 — Electrical Characteristics. 1.1. Absolute Maximum Ratings*. 1.2. DC … |
| Formato / tamaño de archivo | PDF / 1.2 Mb |
| Idioma del documento | Inglés |
Electrical Characteristics. 1.1. Absolute Maximum Ratings*. 1.2. DC Characteristics. Table 1-1. Symbol. Parameter. Condition. Min. Typ. Max
Línea de modelo para esta hoja de datos
Versión de texto del documento
link to page 3 link to page 3 link to page 3 link to page 3 link to page 3 link to page 3 link to page 3 link to page 3 link to page 3
1. Electrical Characteristics 1.1 Absolute Maximum Ratings*
Operating Temperature.. -55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- Storage Temperature ... -65°C to +150°C age to the device. This is a stress rating only and functional operation of the device at these or Voltage on any Pin except RESET other conditions beyond those indicated in the with respect to Ground ..-0.5V to V operational sections of this specification is not CC+0.5V implied. Exposure to absolute maximum rating Voltage on RESET with respect to Ground..-0.5V to +13.0V conditions for extended periods may affect device reliability. Maximum Operating Voltage .. 6.0V DC Current per I/O Pin ... 40.0 mA DC Current VCC and GND Pins.. 200.0 mA
1.2 DC Characteristics Table 1-1.
DC Characteristics. T = -40°C to +125°C A
Symbol Parameter Condition Min. Typ. Max. Units
V = 1.8V - 2.4V 0.2V V CC CC IL Input Low Voltage -0.5 V VCC = 2.4V - 5.5V 0.3VCC (1) Input High-voltage V 0.7V CC = 1.8V - 2.4V CC +0.5(2) V Except RESET pin V = 2.4V - 5.5V (1) VCC CC 0.6VCC VIH Input High-voltage V = 1.8V to 5.5V 0.9V (1) V RESET pin CC CC CC +0.5(2) V Output Low Voltage(3) I 0.7 V OL = 10 mA, VCC = 5V OL V Except RESET pin(5) IOL = 5 mA, VCC = 3V 0.6 Output High-voltage(4) I 4.2 V OH = -10 mA, VCC = 5V OH V Except RESET pin(5) IOH = -5 mA, VCC = 3V 2.4 Input Leakage Vcc = 5.5V, pin low ILIL <0.05 2 µA Current I/O Pin (absolute value) Input Leakage Vcc = 5.5V, pin high ILIH <0.05 2 µA Current I/O Pin (absolute value) R Reset Pull-up Resistor Vcc = 5.5V, input low 30 60 kΩ RST RPU I/O Pin Pull-up Resistor Vcc = 5.5V, input low 20 50 kΩ
2 ATtiny4/5/9/10
8127D–Appendix A–AVR–08/11 Document Outline Appendix A – ATtiny4/5/9/10 Specification at 125°C 1. Electrical Characteristics 1.1 Absolute Maximum Ratings* 1.2 DC Characteristics 1.3 Speed 1.4 Clock Characteristics 1.4.1 Accuracy of Calibrated Internal Oscillator 1.4.2 External Clock Drive 1.5 System and Reset Characteristics 1.5.1 Power-On Reset 1.5.2 VCC Level Monitor 1.6 Analog Comparator Characteristics 1.7 ADC Characteristics (ATtiny5/10, only) 1.8 Serial Programming Characteristics 2. Typical Characteristics 2.1 Active Supply Current 2.2 Idle Supply Current 2.3 Power-down Supply Current 2.4 Pin Pull-up 2.5 Pin Driver Strength 2.6 Pin Threshold and Hysteresis 2.7 Analog Comparator Offset 2.8 Internal Oscillator Speed 2.9 VLM Thresholds 2.10 Current Consumption of Peripheral Units 2.11 Reset Pulsewidth 3. Ordering Information 3.1 ATtiny4 3.2 ATtiny5 3.3 ATtiny9 3.4 ATtiny10 4. Revision History
1. Electrical Characteristics 1.1 Absolute Maximum Ratings*
Operating Temperature.. -55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- Storage Temperature ... -65°C to +150°C age to the device. This is a stress rating only and functional operation of the device at these or Voltage on any Pin except RESET other conditions beyond those indicated in the with respect to Ground ..-0.5V to V operational sections of this specification is not CC+0.5V implied. Exposure to absolute maximum rating Voltage on RESET with respect to Ground..-0.5V to +13.0V conditions for extended periods may affect device reliability. Maximum Operating Voltage .. 6.0V DC Current per I/O Pin ... 40.0 mA DC Current VCC and GND Pins.. 200.0 mA
1.2 DC Characteristics Table 1-1.
DC Characteristics. T = -40°C to +125°C A
Symbol Parameter Condition Min. Typ. Max. Units
V = 1.8V - 2.4V 0.2V V CC CC IL Input Low Voltage -0.5 V VCC = 2.4V - 5.5V 0.3VCC (1) Input High-voltage V 0.7V CC = 1.8V - 2.4V CC +0.5(2) V Except RESET pin V = 2.4V - 5.5V (1) VCC CC 0.6VCC VIH Input High-voltage V = 1.8V to 5.5V 0.9V (1) V RESET pin CC CC CC +0.5(2) V Output Low Voltage(3) I 0.7 V OL = 10 mA, VCC = 5V OL V Except RESET pin(5) IOL = 5 mA, VCC = 3V 0.6 Output High-voltage(4) I 4.2 V OH = -10 mA, VCC = 5V OH V Except RESET pin(5) IOH = -5 mA, VCC = 3V 2.4 Input Leakage Vcc = 5.5V, pin low ILIL <0.05 2 µA Current I/O Pin (absolute value) Input Leakage Vcc = 5.5V, pin high ILIH <0.05 2 µA Current I/O Pin (absolute value) R Reset Pull-up Resistor Vcc = 5.5V, input low 30 60 kΩ RST RPU I/O Pin Pull-up Resistor Vcc = 5.5V, input low 20 50 kΩ
2 ATtiny4/5/9/10
8127D–Appendix A–AVR–08/11 Document Outline Appendix A – ATtiny4/5/9/10 Specification at 125°C 1. Electrical Characteristics 1.1 Absolute Maximum Ratings* 1.2 DC Characteristics 1.3 Speed 1.4 Clock Characteristics 1.4.1 Accuracy of Calibrated Internal Oscillator 1.4.2 External Clock Drive 1.5 System and Reset Characteristics 1.5.1 Power-On Reset 1.5.2 VCC Level Monitor 1.6 Analog Comparator Characteristics 1.7 ADC Characteristics (ATtiny5/10, only) 1.8 Serial Programming Characteristics 2. Typical Characteristics 2.1 Active Supply Current 2.2 Idle Supply Current 2.3 Power-down Supply Current 2.4 Pin Pull-up 2.5 Pin Driver Strength 2.6 Pin Threshold and Hysteresis 2.7 Analog Comparator Offset 2.8 Internal Oscillator Speed 2.9 VLM Thresholds 2.10 Current Consumption of Peripheral Units 2.11 Reset Pulsewidth 3. Ordering Information 3.1 ATtiny4 3.2 ATtiny5 3.3 ATtiny9 3.4 ATtiny10 4. Revision History