Datasheet Linear Technology LTC2379CMS-18#PBF — Ficha de datos

Hojas de datos

Precios

Embalaje

Paramétricos

Plan ecológico

Notas de aplicación

• Descargar
  Fidelity Testing for A to D Converters &mdash AN132
  PDF, 3.8 Mb, Archivo publicado: oct 1, 2011
  The ability to faithfully digitize a sine wave is a sensitive test of high resolution A to D converter fidelity. This test requires a sine wave generator with residual distortion products approaching one part-per-million. Additionally, a computer-based A to D output monitor is necessary to read and display converter output spectral components. Performing this testing at reasonable cost and complexity requires construction of its elements and performance verification prior to use.
  Extracto del documento

  Application Note 132
  February 2011
  Fidelity Testing for A→D Converters
  Proving Purity
  Jim Williams and Guy Hoover
  Introduction
  The ability to faithfully digitize a sine wave is a sensitive
  test of high resolution A→D converter fidelity. This test
  requires a sine wave generator with residual distortion
  products approaching one part-per-million. Additionally,
  a computer-based A→D output monitor is necessary to
  read and display converter output spectral components.
  Performing this testing at reasonable cost and complexity
  requires construction of its elements and performance
  verification prior to use.
  Overview
  Figure 1 diagrams the system. A low distortion oscillator
  drives the A→D via an amplifier. The A→D output interface
  formats converter output and communicates with the
  computer which executes the spectral analysis software
  and displays the resulting data.
  Oscillator Circuitry
  The oscillator is the system’s most difficult circuit design …

Notas de Diseño

• Descargar
  Driving a Low Noise, Low Distortion 18-Bit, 1.6Msps ADC &mdash DN494
  PDF, 1.1 Mb, Archivo publicado: agosto 1, 2011
  Extracto del documento

  Driving a Low Noise, Low Distortion 18-Bit, 1.6Msps ADC
  Design Note 494
  Guy Hoover
  Introduction
  The LTC В®2379-18 is an 18-bit, 1.6Msps SAR ADC with
  an extremely high SNR of 101dB and THD of –120dB. It
  also features a unique digital-gain compression function,
  which eliminates the need for a negative supply in the
  ADC driver circuit. the LTВ®6203 and minimizes disturbances reflected into
  the LT6203 from sampling transients. The 32k point FFT
  in Figure 2 shows the performance of the LTC2379-18 in
  the circuit of Figure 1.
  Single Supply Driver
  The circuit of Figure 3 uses the digital gain compression
  feature of the LTC2379-18, which defines the ADC full-scale
  input swing to be 10% to 90% of the reference voltage.
  This means that for a 5V reference the full-scale swing is Designing a driver circuit to get the best possible performance from the LTC2379-18 is not difficult. The two
  circuits presented here demonstrate differential and
  single-ended solutions using dual and single supplies.
  Note that the components used here have been carefully
  chosen with the ADC’s accuracy and acquisition time
  requirements in mind, so any modifications should be
  thoroughly tested. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of …

Artículos

• Descargar
  Low Power, DC Accurate Drivers for 18-Bit ADCs &mdash LT Journal
  PDF, 3.4 Mb, Archivo publicado: jul 9, 2013
  Extracto del documento

  Low Power, DC Accurate Drivers for 18-Bit ADCs
  Guy Hoover A common misconception about 18-bit SAR ADCs is the only way to drive them
  is with a high powered, high speed, low noise op amp or differential driver whose
  DC performance often leaves much to be desired. It is possible to use a low
  power, DC accurate op amp to drive an 18-bit SAR ADC if the input is a DC or low
  bandwidth AC signal and the op amp outputs are given sufficient time to settle.
  Using the single-ended to differential driver of Figure 1, four different low power
  dual op amps were tested to show the trade-offs in using low power drivers.
  This circuit enables the testing of offset voltage, the maximum sample
  rate for DC and AC signals, noise and
  power consumption. The ADC used
  is the LTC2379-18, a 1.6Msps 18-bit
  SAR ADC with an offset of В±9LSBs, INL of
  В±2LSBs and peak-to-peak noise of 5LSBs.
  The four amplifiers used are the
  LT1013, LTC6078, LTC6081 precision and
  LTC2051HV zero-drift dual op amps—
  Table 1 shows a summary of their major
  specs. The circuit supply voltage is the
  voltage applied to the V+ and V– terminals
  of the op amps. This voltage determines
  the power dissipation of the amplifier and
  its maximum signal swing. The voltages …

Linea modelo

Clasificación del fabricante

• Data Conversion > Analog-to-Digital Converters (ADC) > Precision ADCs (Fs < 10Msps) > Single Channel ADCs
• Space & Harsh Environment > Extended Temperature Plastic (H & MP) > Extended Temperature (H & MP) ADCs

Otros nombres:

LTC2379CMS-18PBF, LTC2379CMS-18 PBF, LTC2379CMS18#PBF, LTC2379CMS 18#PBF