Datasheet Analog Devices AD8599TRZ-EP-R7 — Ficha de datos

REVISIONS
LTR DESCRIPTION DATE Prepared in accordance with ASME Y14.24 APPROVED Vendor item drawing REV
PAGE
REV
PAGE
REV STATUS
OF PAGES REV
PAGE 1 2 PMIC N/A PREPARED BY
RICK OFFICER Original date of drawing
YY-MM-DD CHECKED BY
RAJESH PITHADIA 15-11-05 4 A
REV 5 6 7 8 9 10 11 DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
MICROCIRCUIT, LINEAR, DUAL ULTRALOW
DISTORTION, ULTRALOW NOISE OPERATIONAL
AMPLIFIER, MONOLITHIC SILICON APPROVED BY
CHARLES F. SAFFLE
SIZE AMSC N/A 3 CODE IDENT. NO. DWG NO. V62/16604 16236
PAGE 1 OF 11
5962-V004-16 1. SCOPE
1.1 Scope. This drawing documents the general requirements of a dual, ultralow distortion, ultralow noise operational amplifier …

PIN CONFIGURATIONS Low noise: 1.1 nV/√Hz at 1 kHz
Low distortion: −120 dB THD at 1 kHz
Input noise, 0.1 Hz to 10 Hz: 2 kΩ is
achieved; the current noise component is larger than the
resistor noise.
100 TOTAL NOISE (nV/ Hz) INPUT VOLTAGE RANGE 10
TOTAL NOISE RESISTOR NOISE
ONLY 1 Output phase reversal occurs in some amplifiers when the input
common-mode voltage range is exceeded. As the common-mode
voltage is moved outside the input voltage range, the outputs of
these amplifiers can suddenly jump in the opposite direction to
the supply rail. This is the result of the differential input pair
shutting down that causes a radical shifting of internal voltages
that results in the erratic output behavior. Rev. F | Page 15 of 20 0.1
10 06274-076 OUTPUT PHASE REVERSAL
100 1k SOURCE RESISTANCE (Ω) Figure 58. Noise vs. Source Resistance 10k AD8597/AD8599 Data Sheet
general noise theory with extensive calculations, see the
AN-358 Application Note, Noise and Operational Amplifier
Circuits. A good selection table for low noise op amps can
be found in AN-940 Application Note, Low Noise Amplifier
Selection Guide for Optimal Noise Performance. An interesting
note on using one section of a monolithic dual to phase compensate the other section is in the AN-107 Application Note, Active
Feedback Improves Amplifier Phase Accuracy. The AD8597/AD8599 are the optimum choice for low noise …

Dual, Ultralow Distortion,
Ultralow Noise Op Amp
AD8599-EP Enhanced Product PIN CONFIGURATION Low voltage noise density: 1.15 nV/√Hz at 1 kHz
Low distortion: −120 dB total harmonic distortion plus noise
(THD + N) at 1 kHz
Peak-to-peak noise: 76 nV p-p at 0.1 Hz to 10 Hz
Slew rate: 15 V/μs at VSY = ±15 V
Wide gain bandwidth product: 10 MHz
Supply current per amplifier: 5.0 mA typical at VSY = ±15 V
Low offset voltage: 10 μV typical at VSY = ±15 V
Common-mode rejection ratio (CMRR): 120 dB minimum
Unity-gain stable
Dual-supply operation: ±15 V OUT A 1
–IN A 2 AD8599-EP +IN A 3 TOP VIEW
(Not to Scale) –V 4 8 +V 7 OUT B 6 –IN B 5 +IN B 13065-001 FEATURES Figure 1. ENHANCED PRODUCT FEATURES
Supports defense and aerospace applications (AQEC standard)
Extended temperature range: −55°C to +125°C
Controlled manufacturing baseline
One assembly/test site
One fabrication site
Enhanced product change notification
Qualification data available on request APPLICATIONS
Professional audio preamplifiers …

PIN CONFIGURATIONS Low noise: 1.1 nV/√Hz at 1 kHz
Low distortion: −120 dB THD at 1 kHz
Input noise, 0.1 Hz to 10 Hz: 2 kΩ is
achieved; the current noise component is larger than the
resistor noise.
100 TOTAL NOISE (nV/ Hz) INPUT VOLTAGE RANGE 10 TOTAL NOISE
RESISTOR NOISE
ONLY
1 Output phase reversal occurs in some amplifiers when the input
common-mode voltage range is exceeded. As the common-mode
voltage is moved outside the input voltage range, the outputs of
these amplifiers can suddenly jump in the opposite direction to
the supply rail. This is the result of the differential input pair
shutting down that causes a radical shifting of internal voltages
that results in the erratic output behavior. Rev. E | Page 15 of 20 0.1
10 06274-076 OUTPUT PHASE REVERSAL
100 1k SOURCE RESISTANCE (Ω) Figure 58. Noise vs. Source Resistance 10k AD8597/AD8599 Data Sheet
general noise theory with extensive calculations, see the
AN-358 Application Note, Noise and Operational Amplifier
Circuits. A good selection table for low noise op amps can
be found in AN-940 Application Note, Low Noise Amplifier
Selection Guide for Optimal Noise Performance. An interesting
note on using one section of a monolithic dual to phase compensate the other section is in the AN-107 Application Note, Active …