Datasheet Linear Technology LT1179ACN#PBF — Ficha de datos

Hojas de datos

Precios

Embalaje

Paramétricos

Plan ecológico

Otras opciones

LT1178 LT1178

Notas de aplicación

• Descargar
  Using the LTC Op Amp Macromodels &mdash AN48
  PDF, 297 Kb, Archivo publicado: nov 8, 1991
  LTC's op amp macromodels are described in detail, along with the theory behind each model and complete schematics of each topology. Extended modeling topics are discussed, such as phase/frequency response modifications and asymmetric slew rate for JFET op amp models. LTC's macromodels are optimized for accuracy and fast simulation times. Simulation times can be further reduced by using streamlining techniques found throughout AN48.
  Extracto del documento

  Application Note 48
  November 1991
  Using the LTC Op Amp Macromodels
  Getting the Most from SPICE and the LTC Library
  Walt Jung INTRODUCTION This application note is an overview discussion of the
  Linear Technology SPICE macromodel library. It assumes
  little if any prior knowledge of this software library or its
  history. However, it does assume familiarity with both the
  analog simulation program SPICE (or one of its many
  derivatives), and modern day op amps, including bipolar,
  JFET, and MOSFET amplifier technologies.
  Some Preliminary SPICE Facts of Life
  In the past few years, SPICE simulations have really begun
  to capture a high level of attention on the part of analog
  circuit designers. Perhaps this is due to more affordable
  high performance computers, or perhaps the time for
  simulation is now upon us. In any event, the bottom line is
  that IC vendors are now making macromodels for op amps
  available to their customers.
  For the analog circuit designer, there can be no better fate
  for simulations, viewing this situation in terms of which
  model to use. Designers no longer need worry about
  whether the third party supplier’s model can really cut it. …

Notas de Diseño

• Descargar
  Chopper vs Bipolar Op Amps—An Unbiased Comparison &mdash DN42
  PDF, 70 Kb, Archivo publicado: dic 1, 1990
  Extracto del documento

  Chopper vs Bipolar Op Amps—An Unbiased Comparison
  Design Note 42
  George Erdi Table 1 lists the parameters of importance. In all input
  parameters (except noise) the advantage unquestionably goes to the choppers. 5ОјV maximum offset voltage, 0.5ОјV/В°C maximum drift are commonly found
  Table 1. Chopper Stabilized vs Precision Bipolar Op Amps
  ADVANTAGE
  PARAMETER
  Offset Voltage
  Offset Drift
  All Other DC Specs CHOPPER BIPOLAR COMMENTS
  вњ“
  вњ“
  вњ“ No Contest Wideband, 20Hz to
  1MHz вњ“ See Details in Text Noise вњ“ See Details in Text вњ“ Rail to Rail Swing
  2mA Limit on
  Choppers Output: Light Load
  Heavy Load
  Single Supply
  Application вњ“ вњ“ Inherent to
  Choppers Needs
  Special Design
  Bipolars В±15V Supply Voltage вњ“ Except LTC1150 Prejudice/Tradition вњ“ Still a Chopper
  Problem Cost 08/90/86_conv вњ“ Unless DC …

• Descargar
  3V Operation of Linear Technology Op Amps &mdash DN56
  PDF, 78 Kb, Archivo publicado: feb 1, 1992
  Extracto del documento

  3V Operation of Linear Technology Op Amps -Design Note 56
  George Erdi
  The latest trend in digital electronics is the introduction
  of numerous ICs operating on regulated 3V or 3.3V
  power supplies. This is a logical development to increase
  circuit densities and to reduce power dissipation. In addition, many systems are directly powered by two AA
  cells or 3V lithium batteries. Clearly, analog ICs which
  work on 3V with good dynamic range to complement
  these digital circuits are, and will be, in great demand.
  Many Linear Technology operational amplifiers work
  well on a 3V supply. The purpose of this design note
  is to list these devices and their performance when
  powered by 3V. The op amps can be divided into two
  groups: single and dual supply devices. The single supply
  op amps are optimized for, and fully specified at, a 5V
  positive supply with the negative supply terminal tied
  to ground. Input common mode voltage range goes
  below ground, and the output swings to within a few
  millivolts of ground while sinking current. Members of
  the single supply family are the micropower LTВ®1077/
  LT1078/LT1079 single, dual and quad op amps with
  40μA supply current per amplifier, the LT1178/LT1179 dual and quad with 13μA per amplifier. The LT1006/
  LT1013/LT1014 single, dual and quad have faster speed …

Linea modelo

Clasificación del fabricante

• Signal Conditioning > Amplifiers > Operational Amplifiers (Op Amps) > Precision Amplifiers (Vos | High Voltage Amplifiers (>12V) | Low Power Amplifiers (Is < 1mA/amp)

Otros nombres:

LT1179ACNPBF, LT1179ACN PBF