Datasheet Texas Instruments OPA637APG4 — Ficha de datos
| Fabricante | Texas Instruments |
| Serie | OPA637 |
| Numero de parte | OPA637APG4 |
Amplificadores operacionales Precision High-Speed Difet® 8-PDIP
Hojas de datos
OPA627 and OPA637 Precision High-Speed DifetВ® Operational Amplifiers datasheet
PDF, 1.4 Mb, Revisión: A, Archivo publicado: abr 16, 2015
Extracto del documento
Precios
Estado
| Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
| Disponibilidad de muestra del fabricante | No |
Embalaje
| Pin | 8 |
| Package Type | P |
| Industry STD Term | PDIP |
| JEDEC Code | R-PDIP-T |
| Package QTY | 50 |
| Carrier | TUBE |
| Device Marking | OPA637AP |
| Width (mm) | 6.35 |
| Length (mm) | 9.81 |
| Thickness (mm) | 3.9 |
| Pitch (mm) | 2.54 |
| Max Height (mm) | 5.08 |
| Mechanical Data | Descargar |
Paramétricos
| Acl, min spec gain | 1.7 V/V |
| Additional Features | Decompensated |
| Architecture | FET,Voltage FB |
| BW @ Acl | 16 MHz |
| CMRR(Min) | 100 dB |
| CMRR(Typ) | 110 dB |
| GBW(Typ) | 80 MHz |
| Input Bias Current(Max) | 5 pA |
| Iq per channel(Max) | 7.5 mA |
| Iq per channel(Typ) | 7 mA |
| Number of Channels | 1 |
| Offset Drift(Typ) | 0.4 uV/C |
| Operating Temperature Range | -25 to 85 C |
| Output Current(Typ) | 45 mA |
| Package Group | PDIP |
| Package Size: mm2:W x L | See datasheet (PDIP) PKG |
| Rail-to-Rail | In,Out |
| Rating | Catalog |
| Slew Rate(Typ) | 100 V/us |
| Total Supply Voltage(Max) | 36 +5V=5, +/-5V=10 |
| Total Supply Voltage(Min) | 9 +5V=5, +/-5V=10 |
| Vn at 1kHz(Typ) | 5.2 nV/rtHz |
| Vn at Flatband(Typ) | 4.5 nV/rtHz |
| Vos (Offset Voltage @ 25C)(Max) | 0.1 mV |
Plan ecológico
| RoHS | Obediente |
Notas de aplicación
- Fast Settling Low-Pass FilterPDF, 101 Kb, Archivo publicado: sept 27, 2000
Noise reduction by filtering is the most commonly used method for improving signal-to-noise ratio. The increase in settling time, however, can be a serious disadvantage in some applications such as high-speed data acquisition systems. The nonlinear filter described here is a simple way to get a four-to-one improvement in settling time as compared to a conventional filter. - Improved Device Noise Performance For the 3650 Isolation AmplifierPDF, 28 Kb, Archivo publicado: sept 27, 2000
The 3650 is an optically coupled, differential input, isolation amplifier having programmable gain. Noise for the 3650 is specified to 4u Vrms (typ) on the input stage of the isolation barrier and 65u Vrms (typ) on the output stage. The gain of the 3650 is controlled using exernal resistors on the input stage. In low gains, the noise performance of the 3650 is dominated by the output stage noise f - OPA627, OPA637 EMI Immunity Performance (Rev. A)PDF, 90 Kb, Revisión: A, Archivo publicado: nov 2, 2012
- Composite Op Amp Gives You The Best of Both WorldsPDF, 32 Kb, Archivo publicado: sept 27, 2000
Classical op amps such as the OPA627 have excellent performance in applications where the required gain bandwidth is low compared to the gain-bandwidth product of the op amp. However, increasing closed-loop gain decreases the error-reducing loop gain. Furthermore, starting at relatively low frequencies, the loop gain rolls-off at 20dB/decade of signal frequency increase. In combination these effec - Comparison of Noise Performance of FET Transimpedence Amp/Switched IntegratorPDF, 66 Kb, Archivo publicado: sept 27, 2000
Low-input current FET operational amplifiers are universlly used to monitor photodetector, or more commonly photodiode currents. These photodetectors bridge the gap between a physical event, light, and electronics. There are a variey of amplifier configurations to select from and the choice is based on noise, bandwidth, offset, and linearity. A considerable amount has been written on the performan - MUX-Friendly: Definition and BenefitsPDF, 212 Kb, Archivo publicado: sept 18, 2017
- Compensate Transimpedance Amplifiers Intuitively (Rev. A)PDF, 69 Kb, Revisión: A, Archivo publicado: marzo 30, 2005
Transimpedance amplifiers are used to convert low-level photodiode currents to usable voltage signals. All too often, the amplifiers have to be empirically compensated to operate properly. The problem can be easily understood if one looks at all the elements involved. - Noise Analysis for High Speed Op Amps (Rev. A)PDF, 256 Kb, Revisión: A, Archivo publicado: enero 17, 2005
As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu
Linea modelo
Serie: OPA637 (13)
Clasificación del fabricante
- Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)