Datasheet Texas Instruments UCC3803PWTRG4 — Ficha de datos

Fabricante	Texas Instruments
Serie	UCC3803
Numero de parte	UCC3803PWTRG4

BiCMOS de baja potencia en modo actual PWM 8-TSSOP 0 a 70

Hojas de datos

Descargar

PDF, 3.0 Mb, Revisión: E, Archivo publicado: jun 27, 2016

Extracto del documento

Precios

Estado

Estado del ciclo de vida	Activo (Recomendado para nuevos diseños)
Disponibilidad de muestra del fabricante	No

Embalaje

Pin	8
Package Type	PW
Industry STD Term	TSSOP
JEDEC Code	R-PDSO-G
Package QTY	2000
Carrier	LARGE T&R
Device Marking	3803
Width (mm)	4.4
Length (mm)	3
Thickness (mm)	1
Pitch (mm)	.65
Max Height (mm)	1.2
Mechanical Data	Descargar

Paramétricos

Control Method	Current
Duty Cycle(Max)	100 %
Frequency(Max)	1000 kHz
Gate Drive(Typ)	1 A
Operating Temperature Range	0 to 70 C
Package Group	TSSOP
Rating	Catalog
Special Features	Error Amplifier,Multi-topology,Soft Start
Topology	Boost,Buck,Flyback,Forward
UVLO Thresholds On/Off	4.1/3.6 V
Vin(Max)	400 V
Vin(Min)	4.1 V

Plan ecológico

RoHS

Obediente

Notas de aplicación

Descargar
Low Voltage Feedback in PWM Applications
PDF, 56 Kb, Archivo publicado: feb 27, 2003
Normally the output voltage of a switching power supply is higher than the error amplifier reference, and so a simple resistive divider between the output voltage and ground at the non-inverting input of the PWM error amplifier is all that is required to set the regulation voltage. However, when the output voltage is less than the error amplifier reference voltage, the feedback voltage must be div
Descargar
Dual Output Boost Converter
PDF, 248 Kb, Archivo publicado: abr 9, 2003
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulation and efficiencies are compared and presented.
Descargar
DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
PDF, 66 Kb, Archivo publicado: sept 5, 1999
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback of the boost topology is that, even with the boost converter off, the output voltage approaches the input voltage and does not go to zero. This
Descargar
DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
PDF, 51 Kb, Archivo publicado: sept 5, 1999
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby mode.
Descargar
DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
PDF, 60 Kb, Archivo publicado: sept 5, 1999
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3803 is part of the UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits, which contains all necessary control and drive compone
Descargar
DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
PDF, 58 Kb, Archivo publicado: sept 5, 1999
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included.
Descargar
DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
PDF, 38 Kb, Archivo publicado: sept 5, 1999
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOSFET or IGBT gate drives at power levels below a few watts. This design note describes a low-power negative output voltage +5 to ?5V inverter usi
Descargar
Differences Between the UCC3813 and the UCC3800 PWM Families
PDF, 27 Kb, Archivo publicado: jun 2, 2000
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments.
Descargar
U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
PDF, 583 Kb, Archivo publicado: sept 5, 1999
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current totem-pole output. The popular UC3842 control-circuit architecture has been recently improved to deliver even higher levels of protection and perfor
Descargar
DN-65 Considerations in Powering BiCMOS ICs
PDF, 100 Kb, Archivo publicado: sept 5, 1999
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers supervisory circuits and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes powering was not a concern. In addition many of these ICs contained high-current protection zeners to keep higher voltages from damaging the devices. With a numb
Descargar
UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
PDF, 280 Kb, Archivo publicado: feb 7, 2002
Since their introduction in the mid 1980?s the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear the devices feature an elegantly simple yet very effective control architecture they use only 8 pins they can drive MOSFET gates directly and they offer
Descargar
U-111 Practical Considerations in Current Mode Power Supplies
PDF, 787 Kb, Archivo publicado: sept 5, 1999
This application note explains the numerous PWM functions and ways to maximize their usefulness. It covers practical circuit design considerations such as slope compensation gate drive circuitry external control functions synchronization and paralleling current-mode controlled modules. Circuit diagrams and simplified equations are included.
Descargar
DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
PDF, 42 Kb, Archivo publicado: sept 5, 1999
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment higher switching frequencies for reduced magnetics size higher levels of circuit integration for improved reliability and lower cost. The UCC3802 family of devices is pin-out compatible with the UC3842 and UC3842A families; however it is not plu
Descargar
Conditioning a Switch-mode Power Supply Current Signal Using TI Op Amps
PDF, 61 Kb, Archivo publicado: marzo 23, 2000
The switch-mode power supply primary current is often sensed using a power resistor. Using an op amp to amplify the current-sense signal can reduce cost and improve noise performance and efficiency. This report reviews the advantages of using an op amp circuit and analyzes the design criteria needed to choose the proper op amp.
Descargar
Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A)
PDF, 363 Kb, Revisión: A, Archivo publicado: mayo 28, 2002

Linea modelo

Serie: UCC3803 (9)

UCC3803D UCC3803DG4 UCC3803DTR UCC3803DTRG4 UCC3803N UCC3803NG4 UCC3803PW UCC3803PWTR UCC3803PWTRG4

Clasificación del fabricante

Semiconductors > Power Management > Offline and Isolated DC/DC Controllers and Converters > PWM and Resonant Controller