Datasheet Texas Instruments OPA657UBG4 — Ficha de datos
| Fabricante | Texas Instruments |
| Serie | OPA657 |
| Numero de parte | OPA657UBG4 |
1.6GHz, bajo ruido, amplificador operacional de entrada FET 8-SOIC -40 a 85
Hojas de datos
OPA657 1.6-GHz, Low-Noise, FET-Input Operational Amplifier datasheet
PDF, 1.3 Mb, Revisión: F, Archivo publicado: agosto 31, 2015
Extracto del documento
Precios
Estado
| Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
| Disponibilidad de muestra del fabricante | Sí |
Embalaje
| Pin | 8 | 8 | 8 |
| Package Type | D | D | D |
| Industry STD Term | SOIC | SOIC | SOIC |
| JEDEC Code | R-PDSO-G | R-PDSO-G | R-PDSO-G |
| Package QTY | 75 | 75 | 75 |
| Carrier | TUBE | TUBE | TUBE |
| Device Marking | B | OPA | 657U |
| Width (mm) | 3.91 | 3.91 | 3.91 |
| Length (mm) | 4.9 | 4.9 | 4.9 |
| Thickness (mm) | 1.58 | 1.58 | 1.58 |
| Pitch (mm) | 1.27 | 1.27 | 1.27 |
| Max Height (mm) | 1.75 | 1.75 | 1.75 |
| Mechanical Data | Descargar | Descargar | Descargar |
Paramétricos
| 2nd Harmonic | 74 dBc |
| 3rd Harmonic | 106 dBc |
| @ MHz | 5 |
| Acl, min spec gain | 7 V/V |
| Additional Features | Decompensated |
| Architecture | FET,Voltage FB |
| BW @ Acl | 350 MHz |
| CMRR(Min) | 83 dB |
| CMRR(Typ) | 89 dB |
| GBW(Typ) | 1600 MHz |
| Input Bias Current(Max) | 20 pA |
| Iq per channel(Max) | 16 mA |
| Iq per channel(Typ) | 14 mA |
| Number of Channels | 1 |
| Offset Drift(Typ) | 2 uV/C |
| Operating Temperature Range | -40 to 85 C |
| Output Current(Typ) | 70 mA |
| Package Group | SOIC |
| Package Size: mm2:W x L | 8SOIC: 29 mm2: 6 x 4.9(SOIC) PKG |
| Rail-to-Rail | No |
| Rating | Catalog |
| Slew Rate(Typ) | 700 V/us |
| Total Supply Voltage(Max) | 12 +5V=5, +/-5V=10 |
| Total Supply Voltage(Min) | 8 +5V=5, +/-5V=10 |
| Vn at 1kHz(Typ) | 7 nV/rtHz |
| Vn at Flatband(Typ) | 4.8 nV/rtHz |
| Vos (Offset Voltage @ 25C)(Max) | 1.8 mV |
Plan ecológico
| RoHS | Obediente |
Kits de diseño y Módulos de evaluación
- Evaluation Modules & Boards: DEM-OPA-SOT-1A
Unpopulated PCB Compatible w/High Speed, Wide Bandwidth Op Amps in SOT(DBV) Pkg
Estado del ciclo de vida: Activo (Recomendado para nuevos diseños) - Evaluation Modules & Boards: DEM-OPA-SO-1A
DEM-OPA-SO-1A Unpopulated PCB Compatible w/High Speed Wide Bandwidth Op Amps in 8-lead SOIC (D) Pkg
Estado del ciclo de vida: Activo (Recomendado para nuevos diseños)
Notas de aplicación
- Transimpedance Considerations for High-Speed Operational AmplifiersPDF, 193 Kb, Archivo publicado: nov 22, 2009
Designing high-resolution detection circuits using photodiodes presents considerable challenges because bandwidth, gain, and input-referred noise are coupled together. This application note reviews the basic issues of transimpedance design, provides a set of detailed design equations, explains those equations, and develops an approach to easily compare potential solutions. - Transimpedance Amplifiers (TIA): Choosing the Best Amplifier for the job (Rev. A)PDF, 153 Kb, Revisión: A, Archivo publicado: mayo 16, 2017
This application note is intended as a guide for the designer looking to amplify the small signal from a photodiode or avalanche diode so that it would be large enough for further processing (e.g. data acquisition) or to trigger some other event in a system. The challenge in doing so, as always, is to not degrade the signal such that it becomes indistinguishable from random noi - Using a decompensated op amp for improved performancePDF, 352 Kb, Archivo publicado: marzo 11, 2005
- Voltage Feedback vs. Current Feedback Op AmpsPDF, 93 Kb, Archivo publicado: nov 30, 1998
This application report contrasts and compares the characteristics and capabilities of voltage and current feedback operational amplifiers. The report also points out the many similarities between the two versions. - Designing for low distortion with high-speed op ampsPDF, 277 Kb, Archivo publicado: marzo 2, 2005
- Measuring Board Parasitics in High-Speed Analog DesignPDF, 134 Kb, Archivo publicado: jul 7, 2003
Successful circuit designs using high-speed amplifiers can depend upon understanding and identifying parasitic PCB components. Simulating a design while including PCB parasitics can protect against unpleasant production surprises. This application report discusses an easy method for measuring parasitic components in a prototype or final PC board design by using a standard oscilloscope and low freq - Noise Analysis for High Speed Op Amps (Rev. A)PDF, 256 Kb, Revisión: A, Archivo publicado: enero 17, 2005
As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu
Linea modelo
Serie: OPA657 (9)
Clasificación del fabricante
- Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)