Datasheet Texas Instruments LM5022MM/NOPB — Ficha de datos
| Fabricante | Texas Instruments |
| Serie | LM5022 |
| Numero de parte | LM5022MM/NOPB |
6-60V Wide Vin, Boost de modo de corriente y controlador SEPIC 10-VSSOP -40 a 125
Hojas de datos
LM5022 60-V Low-Side Controller for Boost and SEPIC datasheet
PDF, 1.5 Mb, Revisión: H, Archivo publicado: dic 16, 2016
Extracto del documento
Precios
Estado
| Estado del ciclo de vida | Activo (Recomendado para nuevos diseños) |
| Disponibilidad de muestra del fabricante | Sí |
Embalaje
| Pin | 10 |
| Package Type | DGS |
| Industry STD Term | VSSOP |
| JEDEC Code | S-PDSO-G |
| Package QTY | 1000 |
| Carrier | SMALL T&R |
| Device Marking | 5022 |
| Width (mm) | 3 |
| Length (mm) | 3 |
| Thickness (mm) | 1.02 |
| Pitch (mm) | .5 |
| Max Height (mm) | 1.07 |
| Mechanical Data | Descargar |
Paramétricos
| Duty Cycle(Max) | 90 % |
| Iout(Max) | 10 A |
| Iq(Typ) | 3.5 mA |
| Operating Temperature Range | -40 to 125 C |
| Package Group | VSSOP |
| Rating | Catalog |
| Regulated Outputs | 1 |
| Special Features | Enable,Frequency Synchronization,UVLO Adjustable |
| Switch Current Limit(Typ) | 10 A |
| Switching Frequency(Max) | 1000 kHz |
| Switching Frequency(Min) | 170 kHz |
| Type | Controller |
| Vin(Max) | 60 V |
| Vin(Min) | 6 V |
| Vout(Max) | 300 V |
| Vout(Min) | 1.25 V |
Plan ecológico
| RoHS | Obediente |
Kits de diseño y Módulos de evaluación
- Evaluation Modules & Boards: LM5022EVAL
60V Wide Vin Low Side Controller for Boost Evaluation Board
Estado del ciclo de vida: Activo (Recomendado para nuevos diseños)
Notas de aplicación
- Demystifying Type II and Type III Compensators Using Op-Amp and OTA for DC/DC CoPDF, 782 Kb, Archivo publicado: jul 11, 2014
- AN-1696 Designing a Boost LED Driver Using the LM5022 (Rev. B)PDF, 238 Kb, Revisión: B, Archivo publicado: mayo 6, 2013
This application report provides a component-by-component design guide for a boost converter-basedLED driver using the LM5022. - Driving LEDs: To Cap or Not to CapPDF, 542 Kb, Archivo publicado: marzo 21, 2007
- AN-1656 Design Challenges of Switching LED Drivers (Rev. A)PDF, 171 Kb, Revisión: A, Archivo publicado: mayo 3, 2013
Using a switching regulator as an LED driver requires the designer to convert a voltage regulator into acurrent regulator. Beyond the challenge of changing the feedback system to control current, the LEDsthemselves present a load characteristic that is much different than the digital devices and other loads thatrequire constant voltage. The LED WEBENCHВ® online design environment predicts and
Linea modelo
Serie: LM5022 (4)
- LM5022MM LM5022MM/NOPB LM5022MME/NOPB LM5022MMX/NOPB
Clasificación del fabricante
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Controller (External Switch)